The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.
MHD Flasher F + G ซีรี่ส์เป็นแอพปรับจูนแฟลชที่สมบูรณ์แบบสำหรับ BMW ของคุณ ซึ่งแตกต่างจากโมดูล piggyback มันสามารถทำการแมป DME ใหม่ได้อย่างสมบูรณ์ในขณะที่ยังคงรักษากลไกความปลอดภัย OEM ทั้งหมด สิ่งนี้ช่วยให้มีประสิทธิภาพสูงสุดความปลอดภัยสูงสุดและความสามารถในการขับขี่ที่เหนือชั้น
---------------------------------------------
OBD กะพริบเต็มรูปแบบ:
คุณสามารถติดตั้ง MHD ได้ที่บ้านและเริ่มจูนได้ทันที! ไม่จำเป็นต้องถอดและส่ง DME ของคุณเพื่อ“ ปลดล็อค” ราคาแพงเพียงแค่ดาวน์โหลดแอพ MHD Flasher F-Series ที่เชื่อมต่อผ่านสายเคเบิล K + DCAN ไปยังอุปกรณ์ Android ของคุณและพอร์ต OBD-II ของยานพาหนะ และภายใน 15-25 นาทีการติดตั้งเริ่มต้นจะเสร็จสิ้น การเปลี่ยนแปลงแผนที่เพิ่มเติมเร็วกว่ามาก - เพียง 1-3 นาที! คุณสามารถเปลี่ยนกลับรถของคุณเป็นแฟลช OEM จากโรงงานได้ทุกเวลาและไม่จำเป็นต้องสำรองข้อมูลครั้งแรก
---------------------------------------------
แผนที่ระยะ 1, ระยะ 2 และ E85 OTS (นอกชั้นวาง) โดย PureBoost:
N55 EWG (ยานพาหนะที่สร้างขึ้นหลัง 07/2013 ด้วยระบบกำจัดขยะอิเล็กทรอนิกส์):
- ด่าน 1 (สูงถึง 360HP / 540NM) (ไม่สามารถใช้ได้กับ M2 และ X4 M40i)
- ด่านที่ 2 (สูงสุด 390HP / 580NM)
- ด่าน 2+ (สูงสุด 430HP / 630NM)
- แผนที่ผสมเอทานอล: ระยะที่ 1, 2 และ 2+ E20 แผนที่สำหรับการผสมเอทานอล 20%
N55 PWG (นิวเมติกสูญเปล่า):
- ด่าน 1 (สูงถึง 340HP / 540NM)
- ด่านที่ 2 (สูงถึง 370HP / 580NM)
- ด่าน 2+ (สูงถึง 400HP / 630NM)
- แผนที่ผสมเอทานอล: ระยะที่ 1, 2 และ 2+ E20 แผนที่สำหรับการผสมเอทานอล 20%
S55 (BMW M3 / M4 F8x):
- ด่าน 1 (สูงถึง 530HP / 700NM)
- ด่านที่ 2 (สูงถึง 560HP / 780NM)
- แผนที่ผสมเอทานอล: ระยะที่ 1, 2 และ 2+ E30 แผนที่สำหรับการผสมเอทานอล 30%
B58:
- ด่านที่ 1 (สูงถึง 420HP / 580NM)
- ด่านที่ 2 (สูงถึง 470HP / 630NM)
- แผนที่ผสมเอทานอล: ระยะที่ 1, 2 แผนที่สำหรับการผสมเอทานอล 30%
---------------------------------------------
ตรวจสอบพฤติกรรมเครื่องยนต์ของคุณเพื่อให้แน่ใจว่าทำงานได้อย่างสมบูรณ์โดยใช้โครงร่างเกจที่ปรับแต่งได้และตอบสนองได้ดีมาก พารามิเตอร์เครื่องยนต์ 50+ สามารถใช้ได้อย่างรวดเร็ว!
นี่คือจอภาพบางส่วนที่มี:
- Boost, Boost Target
- แลมบ์ดา (AFR)
- Intake Air Temp (IAT)
- เวลาติดไฟต่อสูบ
- อุณหภูมิน้ำหล่อเย็น
- อุณหภูมิน้ำมันแรงดันน้ำมัน
- อุณหภูมิการส่ง
- ปั๊มเชื้อเพลิงแรงดันสูง (HPFP)
- ตำแหน่งปีกผีเสื้อ
- วัฏจักรหน้าที่ (WGGGET)
- RPM
- ความเร็ว
- EGT
และอื่น ๆ อีกมากมาย…
MHD มอนิเตอร์ขั้นสูงพิเศษ:
- แก้ไขเวลาต่อสูบ
- เพิ่มเป้าหมาย EX ซึ่งสามารถอ่านได้สูงกว่า 22.x psi (ช่องเพิ่มเป้าหมาย BMW ไม่สามารถทำได้)
- แกนคอมเพรสเซอร์พื้นฐาน: Boost Setpoint, MAF req WGDC
- ตัว จำกัด แรงบิดที่ใช้งานอยู่
และอื่น ๆ อีกมากมาย…
---------------------------------------------
ตัวเลือกแฟลชเหล่านี้สามารถใช้กับแผนที่ใดก็ได้โดยตรงผ่านแอพ:
- Exhaust Burble (ระยะเวลาและความก้าวร้าวความเร็วขั้นต่ำรอบต่อนาที)
- เซ็นเซอร์แผนที่ N20 (บน N55)
- ลบตัว จำกัด ความเร็วสูงสุด (Vmax)
- ลดเสียงรบกวนเริ่มเย็น
- พนังไอเสียเปิดในโหมดกีฬา
- จำกัด พลังต่อเกียร์
- รองรับแฟลช XHP TCU (ปรับแผนที่ OTS ให้เหมาะสม)
- โหมดคูลลิ่งสปอร์ตสำหรับระบายความร้อนด้วยน้ำ / อากาศเย็นมากขึ้น (เพียง 58 บาท)
---------------------------------------------
รถยนต์ที่รองรับ:
M135i F2x N55 2012 - 2016
M235i F2x N55 2556 - 2559
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2558 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive รองรับรถยนต์ทุกคัน
รองรับรถยนต์พลังงานประสิทธิภาพชุดทั้งหมด
ตรวจสอบหน้าแรก / คู่มือผู้ใช้ของเราสำหรับข้อมูลเพิ่มเติมและการปรับเปลี่ยนที่แนะนำสำหรับแต่ละขั้นตอน
The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.